Main item Manufacturers, Suppliers in

Bushing Pulleys

All types of pulleys are combined transmission parts, which will lead to smoother, less noisy, and less vibration production.

Taper Bush for Timing pulley are all screw-thread, won’t have any swinging issue. It’s quick and cost less while replacing the pulley, easy to install/dissemble, and can reduce the manpower.

QD type pulleys are all screw-thread, won’t have any swinging issue. It’s quick and cost less while replacing the pulley, easy to install/dissemble, and can reduce the manpower.

LOCKs are bushes with no keybar connection, but with high tension bolts pulling, causing a strong connection between the rings and hubs.

Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

V-belts

V-belts are from Taiwanese brand ARESTBUSH

V-belts are the most frequent and most kinds among all transmission belts, especially when it comes to industrial drive and transportation apply.

As for high tension v-belt, it contains higher strength tension line, which contributes to more steady power transmit, more stable and longer lifetime. Are commonly seen for fans and AHU.

Material: Rubber
Temperature resistance: White brand 70°C, Red brand 80°C, as for the 80-90°C are the highest standard among the world nowadays

Feel free to ask and place order from us, even for the non-standard products.

Dynamic Balancing Service

Reduce the dynamic unbalance of the rotor, make the machine run smoothly, improve the performance and quality of the work piece, and ensure equipment safety.

The dynamic balancing grade is named G. The smaller the number, the higher the accuracy.

G2.5 is the international standard (currently the accuracy of all types of dynamic balancing machines can reach this level)

G6.3 is a lower-level (standard from 40 years ago)

G1.0 and G0.4 are our company’s highest accuracy currently.

(G0.4 is also the highest correction accuracy among current world standards)

Generally speaking, it is recommended to perform dynamic balance correction when the rotation speed is above 100.

To extend the mechanical life, reduce noise, and improve the overall level;

And if the speed reaches more than 1500 rpm, dynamic balance must be done.

Otherwise, the machine is prone to various operational problems, and may even cause work piece vibration (cracks, damage, short lifespan), increased noise decibels (increased industrial safety hazards), and many other problems.

Take a practical example:

Every time the machine makes one spin, the belt will also vibrate. It is reasonable to estimate that the belt will float up due to this, causing the machine to vibrate and causing many problems.

Calibrated low-vibration rotor advantages:

1. Reduce equipment vibration

2. Extended bearing life

3. Machine production is smooth

4. Reduce resonance and common frequency effects

5. Reduce factory noise decibels

1. Dynamic balancing machine brand: mainly German SCHENCK

2. Execution location: Taiwan

3. For each dynamic balance correction, our company will provide data reports before and after correction. Only true and exact data can ensure true accuracy.

4. Dynamic balance correction includes work piece receiving and delivery. If express processing is required, our company can also meet customer needs.

5. Our company has professional engineers who can customize overall dynamic balance correction needs for customers (including design and production of tooling and fixtures);

Including on-site measurement, overall demand planning, work piece maintenance or replacement time assessment, and overall SOP plan

If you have this need, please contact ARESTBUSH and we will have someone to serve you

TEL:886-6-2337799

FAX:886-6-2331199

Sales Department
E-Mail:ares-chain@umail.hinet.net

Business hours: Monday to Friday 08:00-18:00

Office
E-Mail:aresbelt@gmail.com

Tainan Retail: No. 36, Lane 68, Wangxing Road, Yongkang District, Tainan City

Feel free to ask and place order from us, even for the non-standard products.

V-belts

Special belt for washing machine, shipped directly from the factory (length = P)

※ Specification (Belt length * width * height): Specification (inch) * 10 * 5.5 mm

1. Material: Rubber

2. Temperature resistance: White brand 70°C, Red brand 80°C, as for the 80-90°C are the highest standard among the world nowadays

Feel free to ask and place order from us, even for the non-standard products.

Special belts for electric

Special belts for electric/intelligent/automatic curtain tracks, accessories for electric opening and closing curtains

1. Material: PU (environmentally friendly)

2. This product is cut from a full roll and is a customized product.

3. Length specification: 6 meters, 10 meters, 12 meters, 20 meters, 50 meters, 100 meters

※ The length specification is the commonly used size for electric opening and closing curtains. If you have special needs, please contact customer service first.

Feel free to ask and place an order from us, even for non-standard products.

Automatic door belt S8M

Belt width 12mm

※Automatic door rails with a belt length of 10 mm can also be installed using this size
※In meters, how many meters do you want to order?
For example, 4 meters = 4 meters
Order 4 pieces and they will be shipped in full 4m lengths

1. Material: Rubber

2. This product is cut from a full roll and is a customized product.

Feel free to ask and place an order from us, even for non-standard products.

Automatic door belt :type A

※This specification is applicable to general or older automatic door operators;
If the original belt is a toothed belt, please check out our other product "S8M Automatic Door Belt".

※The length specification is the commonly used automatic door belt size.
If you have special needs, please contact customer service first.

1. Material: Rubber
2. This product is cut from a full roll and is a customized product.

Feel free to ask and place an order from us, even for non-standard products.

V-belts

V-belts are from Taiwanese brand ARESTBUSH

V-belts are the most frequent and most kinds among all transmission belts, especially when it comes to industrial drive and transportation apply.

As for high tension v-belt, it contains higher strength tension line, which contributes to more steady power transmit, more stable and longer lifetime. Are commonly seen for fans and AHU.

1.Material: Rubber
2.Temperature resistance: White brand 70°C, Red brand 80°C, as for the 80-90°C are the highest standard among the world nowadays

Feel free to ask and place order from us, even for the non-standard products.

High tension Wrapped V-belts

V-belts are from Taiwanese brand ARESTBUSH

V-belts are the most frequent and most kinds among all transmission belts, especially when it comes to industrial drive and transportation apply.

As for high tension v-belt, it contains higher strength tension line, which contributes to more steady power transmit, more stable and longer lifetime. Are commonly seen for fans and AHU.

Material: Rubber
Temperature resistance: White brand70°C, Red brand80°C, as for the 80-90°C are the highest standard among the world nowadays

Feel free to ask and place order from us, even for the non-standard products.

Timing Belt

Timing-belts are from Taiwanese brand ARESTBUSH

Mainly used for transmit and have less than 1% power lost while transmitting, which is highly accurate.

Material: Rubber(standard), PU(special)
Tooth type: trapezoid, round
Temperature resistance: permanent 70°C, instant 90°C

Feel free to ask and place order from us, even for the non-standard products.

Cogged Belt

V-belts are from Taiwanese brand ARESTBUSH

Cogged belts have steady cog structure, fit the pulley more than traditional v-belts, can process more power, and endure under more side pressure.

Fits for smaller, higher precision, and high speed pulleys. Can lower the maintenance cost. Especially suitable for automobile, fans, and air conditioners.

Material: Rubber(CR)

Temperature resistance: EPDM110-140°C

Feel free to ask and place order from us, even for the non-standard products.

Multi-rib belts

Belts are from Taiwanese brand ARESTBUSH

Multi-rib belts are one-piece molding, which will make transmission smoother.

With well-mixed material, and stable tension-line, will reduce the balancing issue cause by high speed operating.

Material: Rubber

Temperature resistance: permanent 70°C, instant 90°C

More than welcome to ask and order from us, even for non-standard products.

Powerband-Cogged Belt

Powerband-Cogged V-belts are from Taiwanese brand ARESTBUSH

Powerband-Cogged V-belts are bonded in a high tension method, will provide the extra strength to the side of the belt. These belts can also ensure the belts are united and operate in straighten line. Furthermore, it can also solve issues like belts jumping or isolate, and to keep the system to have a longer lifetime.

Material: Rubber(CR)

Temperature resistance: EPDM110-140°C

Feel free to ask and place order from us, even for the non-standard products.

Taper Bushing Pulleys

All types of pulleys are combined transmission parts, which will lead to smoother, less noisy, and less vibration production.

Material: Cast iron(GG25/FCD250, less long-wearing),Ductile cast iron(GGG450~650, higher level), Stainless Steel(SUS304)
Procedure: Can lower the radial jump
Anti-rust procedure: Phosphate treatment
The tolerance between QD bush and axis: +0.05mm~ -0.125mm
The diameter of pulleys with available stocking: 56~1500mm
Concentric circles:the Bushes fit 360° with the axis, can prevent the gap as the simple bore type might cause.
Can customize various kinds of material, diameter, and groove; and can deliver quickly
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

QD Type Pulley

All types of pulleys are combined transmission parts, which will lead to smoother, less noisy, and less vibration production.

QD type pulleys are all screw-thread, won’t have any swinging issue. It’s quick and cost less while replacing the pulley, easy to install/dissemble, and can reduce the manpower.

Material: Cast iron(GG25/FCD250, less long-wearing) / Ductile cast iron(GGG450~650, higher level)
Procedure: Can lower the radial jump
Anti-rust procedure: Phosphate treatment
The tolerance between QD bush and axis: ±0.125mm
The diameter of pulleys with available stocking: 90~500mm
Concentric circles: the QD bushes fit 360° with the axis, can prevent the gap as the simple bore type might cause.
QD transmission parts are mainly used for pulleys and sprockets, which may frequently need high speed and stable quality. ARESTBUSH can customize for different conditions, and deliver quickly
G2.5 dynamic balancing is highly recommended, to prevent belt from jumping during operating
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Timing Pulley

All types of pulleys are combined transmission parts, which will lead to smoother, less noisy, and less vibration production.

Taper Bush for Timing pulley are all screw-thread, won’t have any swinging issue. It’s quick and cost less while replacing the pulley, easy to install/dissemble, and can reduce the manpower.

Material: Aluminum, Steel(S45C), Cast iron(GG25), Stainless steel(SUS304/316)
Number of tooth:8~
Anti-rust procedure: Phosphate treatment
Procedure: Can lower the radial jump
Tooth type: trapezoid, round
QD Bush for Timing pulley and all kinds of two-part pulleys can be deliver quickly(can customize various kind of material and bushes)
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

LOCK

LOCKs are bushes with no keybar connection, but with high tension bolts pulling, causing a strong connection between the rings and hubs.

Commonly seen in medium or light mechanism use such as wind power generation, packaging machinery, printing machinery, CNC machine tools, automation equipment electronics factories, printing industry, high-speed output industry

Suitable for various modular parts to be matched in low vibration mode (high vibration components must undergo dynamic balance correction to G2.5 level to avoid loosening)

Material: Steel(S45C)
Suitable power horse range: 1~500HP
Anti-rust procedure
Procedure: Can lower the radial jump
Type: heavy-duty type, front stop type, flange fixed type, reduced mouth type, traditional type, universal type
Common parts: flywheel, pulley
Advantages: The use of expansion sleeves makes the manufacturing and installation of host parts simple; the expansion sleeves have a long service life and high strength; the expansion sleeves are easy to disassemble and have good interchangeability
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Roller chains

Suitable for assembling various types of parts: sprockets, couplings and other components.
Commonly used in slow speed transmission and transportation: small powered agricultural vehicles, tractors, mechanical processing equipment, textile machinery, packaging machinery, air compressors, reducers, reducers, generators, etc.

The light transmission part of the chain is partially replaced by a timing belt.

Material: Steel(S45C), Stainless steel(SUS304)
Type: Single, double, triple row
Anti-rust procedure: Phosphate treatment
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Master Link Chain

The clip is the object that connects the two ends of the chain, and has two types: CL & OL.

As for the CL, it is divided into two types according to different fixing methods: C ring, Y ring.

1. Material: Steel (S45C) + heat treatment, Stainless steel (SUS304)
(Strength according to international standards)

2. Type: Single, double, triple row / CL, OL

3. Made in China

Feel free to ask and place an order from us, even for the non-standard products.

Industrial Chains

The clip is the object that connects the two ends of the chain, and has two types: CL&OL.

As for the CL, are divided into two type according to different fixing methods : C ring, Y ring

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double, triple row/CL,OL
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Heavy Duty Chains

The clip is the object that connects the two ends of the chain, and has two types: CL&OL.

As for the CL, are divided into two type according to different fixing methods : C ring, Y ring

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double, triple row/CL,OL
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Stainless Steel Chains CL

The clip is the object that connects the two ends of the chain, and has two types: CL&OL.

As for the CL, are divided into two type according to different fixing methods : C ring, Y ring

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double, triple row/CL,OL
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Half Link Chain

The clip is the object that connects the two ends of the chain, and has two types: CL&OL.

As for the CL, are divided into two type according to different fixing methods : C ring, Y ring

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double, triple row/CL,OL
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Industrial Roller Chain

The clip is the object that connects the two ends of the chain, and has two types: CL&OL.

As for the CL, are divided into two type according to different fixing methods : C ring, Y ring

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double, triple row/CL,OL
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Link Chains CL

The clip is the object that connects the two ends of the chain, and has two types: CL&OL.

As for the CL, are divided into two type according to different fixing methods : C ring, Y ring

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double, triple row/CL,OL
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Alloy Chains

The clip is the object that connects the two ends of the chain, and has two types: CL&OL.

As for the CL, are divided into two type according to different fixing methods : C ring, Y ring

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double, triple row/CL,OL
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Attachment Roller Chain

The clip is the object that connects the two ends of the chain, is CL type.
Can be match single or double pitch; one or both side
As for the CL, are divided into two type according to different fixing methods : C ring, Y ring
With specific needs, chain plates are needed, there are 90°&180°, commonly used in convey related industries.

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double pitch/one or both side/ c or y ring/90° or 180°
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Conveyor Chains

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double pitch/one or both side/ c or y ring/90° or 180°
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Transmission Chain

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double pitch/one or both side/ c or y ring/90° or 180°
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Double Pitch Roller Chain Clip

Material: Steel(S45C)+heat treatment, Stainless steel(SUS304)

(Strength according to international standards)

Type: Single, double pitch/one or both side/ c or y ring/90° or 180°
Made in China

Feel free to ask and place order from us, even for the non-standard products.

Type B Sprocket

We have all types of two-part pulleys and sprockets. The hub format is standard and has plenty of type.
While enhancing the hub, the strength and lifetime of the sprocket will also increase, and transmit the roller chain better, can also adjust in either high or low temperature condition.
B-type sprocket are fit for standard European chain standard, while equip with the matching pitch, lead to less vibration while transmitting.

Both B-type and C-type sprockets are simple-bore, which will easily cause tolerance between bore and axis, and are harder to install; therefore nowadays users tend to replace them with taper bush-type sprockets.

Material: Steel(S45C), Stainless steel(SUS304)
Tooth number: 8~300
Anti-rust procedure: Black Oxide/ In order to meet up with environmental friendly, less black oxide nowadays
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Lock Sprocket

We have all types of two-part sprockets. As for the Taper-bushing type sprockets, it comes with easier construction, lower maintenance cost, easier to install and adjust.

While enhancing the hub, the strength and lifetime of the sprocket will also increase, and transmit the roller chain better, can also adjust in either high or low temperature condition.

Material: Steel(S45C)
Tooth number: 8~60
Anti-rust procedure: Phosphate treatment
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Taper Lock Sprocket

Material: Steel(S45C)
Tooth number: 8~60
Anti-rust procedure: Phosphate treatment
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Conveyor sprockets

We have all types of two-part sprockets.

QD-type sprockets construct with all screw-thread, can avoid the swinging issue for the machine parts. While installing, it’s quicker, easier, and safier.

QD-type sprockets enhance the strength and endurance, while the teeth of the sprocket might been torn, the QD steel bush can still be reuse.

Material: Steel(S45C), Stainless steel(SUS304)
Tooth number: 8~300
Anti-rust procedure: Black Oxide/ In order to meet up with environmental friendly, less black oxide nowadays
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Motor Couplings

Couplings have the characteristics of small structural size, light weight, small moment of inertia but high transmitted torque. They can effectively improve the operating quality and stability of machinery and extend the working life.
The coupling buffers the vibration during transmission and absorbs the impact caused by the uneven operation of the power machine. It is suitable for high-load driving equipment such as: rolling mills, elevators, spline bushings, etc.

This is the basic design, if needing superior version, can look for RU or GR couplings

Material: Cast iron(GG25), Steel(S45C)
Can be applied in general environment
With small diameter and can be suitable for small motor
Comes with a rubber in between
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Flexible Shaft Coupling

Elastic couplings have the characteristics of small structural size, light weight, small moment of inertia but high transmitted torque. They can effectively improve the operating quality and stability of machinery and extend the working life.
The transmission is a zero-backlash design.
The coupling buffers the vibration during transmission and absorbs the impact caused by the uneven operation of the power machine.
Suitable for low, medium and high torque equipment, such as: rolling mills, elevators, spline bushings, etc.

Material: Aluminum, Cast iron(GG25), Steel(S45C), Stainless steel
Can be applied in corrosiveness environment
With small diameter but strong transmitting power
Temperature resistance: -40~+100°C (Instant 120°C)
Purple rubber are the most flexible, then red and then yellow. Other colours are not recommended.
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

HRC Coupling

The rubber coupling is simple in design and easy to disassemble and assemble.
You can choose a taper bush type HRC coupling, which is easy to disassemble and has high concentricity.
With larger torque range used and close to the limit, dynamic balance must be done to level G2.5.

It is suitable for chemical plants, generators, equipment with large axis vibration, etc.

Material: Cast iron(GG25)
Suitable power horse range: 0.1~200HP
With wide range of transmission field
Can tolerance larger range of eccentricity
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Roller Chain Coupling

The chain coupling is composed of two rows of roller chains and sprockets. It has excellent transmission efficiency and can be used as a powerful flexible coupling for all common transmissions.
Suitable for transmission in the rear section of the reducer, suitable for transmission below RPM100

Suitable for high-torque transmission of conveyor belts, excavators, pumps, mixers, etc.

Material: Steel(S45C), Stainless steel(SUS316)
Suitable for rotors with lower and medium speed, and high vibration
With larger torque force
Temperature resistance: -10~+100°C
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Rubber flexible coupling

The NM coupling is simple in design and easy to disassemble and assemble.
The transmission output belongs to medium and low torque. If it is used at high speed, dynamic balance must be done to level G2.5 to show the coupling efficiency.

It is suitable for chemical plants, generators, equipment with large axis vibration, etc.

Material: Cast iron(GG25), Ductile cast iron(GGG450~650)
Suitable power horse range: 0.1~200HP
Ductile cast iron can carry larger torque force
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Industrial Coupling

The rubber structure, with screws as pillars, is a better designed coupling structure.
Steel couplings are more recommended. Only after G2.5 dynamic balance can prevent the need to be corrected again after two years of use.
A taper bush structure can be selected to improve concentric operation.

Material: Steel(S45C), Stainless steel(SUS316), Cast iron(GG25)
Can be applied in corrosiveness environment
With larger torque force and lower vibration
Temperature resistance: -40~+100°C (Instant 120°C)
Suitable power horse range: 0~800HP
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Tyre Coupling

Also known as a safety coupling, the tyre coupling is simple in design and easy to disassemble and assemble; the tire can be replaced without moving the two half couplings.
This type of coupling has the largest deflection angle, 2-20 degrees, and does not require laser alignment installation; it is the coupling structure with the lowest installation cost.

Suitable for chemical plants, generators, and equipment with large axis vibrations. Its characteristic is that when the rubber sleeve is damaged, there will be no metal collision or sparks, which can avoid the risk of fire.

Material: Steel(S45C), Stainless steel(SUS304)
Suitable power horse range: 0.1~600HP
With bigger transmission power
Can tolerance larger range of eccentricity
Safety: When the rubber is torn, there won’t be metal to collide and won’t have sparkle issue. Can prevent the danger of fire
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Taper Bushing Bolt-on Hubs SM

Use bolts to fix the sheet workpiece to the surface of Bolt-on hubs
Workpieces using Bolt-on hubs must undergo dynamic balance G2.5 level.
Can come with either taper or QD bushes, to improve concentricity during operation.

Suitable for fan industry

Material: Cast iron(GG25), Steel(S45C), Stainless steel(SUS304)
Horse power range:0-500HP
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Weld On Sprocket Hubs

It can alleviate load impact and play a moderating role.
It can be connected to the external workpiece by welding, and a tapered or QD bushes can be used to run on the shaft.
Suitable for e.g. expansion of knives.

Material: Steel(S45C), Stainless steel(SUS304)
Horse power range:0-500HP
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Weld On Wheel Hubs

Material: Steel(S45C), Stainless steel(SUS304)
Horse power range:0-500HP
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Spur Gears

Spur gears are cylindrical gears with tooth ribs parallel to the axis. Because they are easy to process, they are the most widely used in power transmission.
Widely used in various industries such as: machine tools, transportation machinery, hoisting machinery, rubber and plastic machinery, woodworking machinery, wind power generation and general industries.

Material: Steel(S45C)
Largest diameter:2000mm
Mold(M): M1-M40
Polish precision: DIN-2, JIS 0, AGMA15
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Taper Bushes

Taper bushes are the cheap type are bushes
Due to taper bushes are only half screw-thread, might cause the machine parts to have swinging issue, so must combined with G2.5 dynamic balancing, which is commonly used with v-pulleys and all type of couplings.

Material: Steel(S45C, standard material), Stainless steel(SUS316), Cast iron(GG25, fragile)
Produce inner bore and keyway according to ISO standard
Transmission device from power horse 0~300HP
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Taper Lock Bushing

Material: Steel(S45C, standard material), Stainless steel(SUS316), Cast iron(GG25, fragile)
Produce inner bore and keyway according to ISO standard
Transmission device from power horse 0~300HP
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

QD Bushing

Within all types of bushes, QD steel bushes are the most adaptable. Constructs with all screw-thread, can avoid the swinging issue for the machine parts.
While using QD bushes, can avoid unnecessary installation error. Also the QD bushes have the least deformation, and with rather long lifetime.
Can apply to all kinds of transmission parts.

Material: Steel(S45C), Stainless steel(SUS304)
Have adequate stocking for standard keyway
Apply horse power range: 1~1000HP
F type requires 3 screws to tighten or disassemble; D type requires 4 screws; E type requires 5screws
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Taper Lock Bush

LOCKs are bushes with no keybar connection, but with high tension bolts pulling, causing a strong connection between the rings and hubs.
Commonly seen in medium or light mechanism use such as wind power generation, packaging machinery, printing machinery, CNC machine tools, automation equipment electronics factories, printing industry, high-speed output industry
Suitable for various modular parts to be matched in low vibration mode (high vibration components must undergo dynamic balance correction to G2.5 level to avoid loosening)

Material: Steel(S45C)
Suitable power horse range: 1~500HP
Anti-rust procedure
Procedure: Can lower the radial jump
Type: heavy-duty type, front stop type, flange fixed type, reduced mouth type, traditional type, universal type
Common parts: flywheel, pulley
Advantages: The use of expansion sleeves makes the manufacturing and installation of host parts simple; the expansion sleeves have a long service life and high strength; the expansion sleeves are easy to disassemble and have good interchangeability
Made in Taiwan

Feel free to ask and place order from us, even for the non-standard products.

Belt Tensioner

Tensioners is a commonly used holding device in belt and chain transmission systems. Its characteristic is to maintain appropriate tension of belts and chains during rotation, thereby preventing belts or chains from slipping and jumping.

Various types of parts suitable for assembly: sprockets, triangle pulleys, synchronous pulleys and other components.

1. Material: Steel (S45C), Stainless steel (SUS304)
2. Made in China

Feel free to ask and place order from us, even for the non-standard products.

Dynamic Balancing Services

Reduce the dynamic unbalance of the rotor, make the machine run smoothly, improve the performance and quality of the work piece, and ensure equipment safety.

The dynamic balancing grade is named G. The smaller the number, the higher the accuracy.
G2.5 is the international standard (currently the accuracy of all types of dynamic balancing machines can reach this level)
G6.3 is a lower-level (standard from 40 years ago)
G1.0 and G0.4 are our company’s highest accuracy currently.
(G0.4 is also the highest correction accuracy among current world standards)

Generally speaking, it is recommended to perform dynamic balance correction when the rotation speed is above 100.
To extend the mechanical life, reduce noise, and improve the overall level;
And if the speed reaches more than 1500 rpm, dynamic balance must be done.
Otherwise, the machine is prone to various operational problems, and may even cause work piece vibration (cracks, damage, short lifespan), increased noise decibels (increased industrial safety hazards), and many other problems.

Take a practical example:
Every time the machine makes one spin, the belt will also vibrate. It is reasonable to estimate that the belt will float up due to this, causing the machine to vibrate and causing many problems.

Calibrated low-vibration rotor advantages:
1. Reduce equipment vibration
2. Extended bearing life
3. Machine production is smooth
4. Reduce resonance and common frequency effects
5. Reduce factory noise decibels

1. Dynamic balancing machine brand: mainly German SCHENCK
2. Execution location: Taiwan
3. For each dynamic balance correction, our company will provide data reports before and after correction. Only true and exact data can ensure true accuracy.
4. Dynamic balance correction includes work piece receiving and delivery. If express processing is required, our company can also meet customer needs.
5. Our company has professional engineers who can customize overall dynamic balance correction needs for customers (including design and production of tooling and fixtures);
Including on-site measurement, overall demand planning, work piece maintenance or replacement time assessment, and overall SOP plan

If you have this need, please contact ARESTBUSH and we will have someone to serve you

TEL:886-6-2337799
FAX:886-6-2331199

Sales Department
E-Mail:ares-chain@umail.hinet.net
Business hours: Monday to Friday 08:00-18:00

Office
E-Mail:aresbelt@gmail.com

Tainan Retail: No. 36, Lane 68, Wangxing Road, Yongkang District, Tainan City

Feel free to ask and place order from us, even for the non-standard products.

Main item Manufacturers, Suppliers in

Bushing Pulleys

V-belts

Dynamic Balancing Service

V-belts

Special belts for electric

Automatic door belt S8M

Automatic door belt :type A

V-belts

High tension Wrapped V-belts

Timing Belt

Cogged Belt

Multi-rib belts

Powerband-Cogged Belt

Taper Bushing Pulleys

QD Type Pulley

Timing Pulley

LOCK

Roller chains

Master Link Chain

Industrial Chains

Heavy Duty Chains

Stainless Steel Chains CL

Half Link Chain

Industrial Roller Chain

Link Chains CL

Alloy Chains

Attachment Roller Chain

Conveyor Chains

Transmission Chain

Double Pitch Roller Chain Clip

Type B Sprocket

Lock Sprocket

Taper Lock Sprocket

Conveyor sprockets

Motor Couplings

Flexible Shaft Coupling

HRC Coupling

Roller Chain Coupling

Rubber flexible coupling

Industrial Coupling

Tyre Coupling

Taper Bushing Bolt-on Hubs SM

Weld On Sprocket Hubs

Weld On Wheel Hubs

Spur Gears

Taper Bushes

Taper Lock Bushing

QD Bushing

Taper Lock Bush

Belt Tensioner

Dynamic Balancing Services

Pulleys Alignment

Wire Drawing Machine Calibration

Fan Balancing

Air Conditioning Box Impeller Balance

High-Speed Mill Balance

High-Pressure Impeller Balancing

Impeller Dynamic Balancing

Rotor Dynamic Balancing

Gear Alignment

Rubber/Plastic Crusher Balance

Coupling Alignment

General Catalog

Belts and Balancing Catalog

ARES Belt vs. Other Brands

How To Choose Belts

High Tension VBelt & Old Power Structure Replacement Diagram

Taper Bushes ISO Metric Bore Diameter And Keyway Comparison

QD steel bushes RMA inch bore & keyway comparison table

QD Pulley Info Introduction

Taper Bush Type Connecting Plate Info

Taper Bush Sprocket Info

Motor Rail Info

Dynamic Balancing Info

Dynamic Balancing Poster (Info for OEM)